WHEN YOU DEMAND HIGH QUALITY AND ACCURACY, GO WITH........ SPEED CITY !

MOPAR
FORD
MISC
PARTS
GM
DRAGSTER
 
Testimonials
Model Gallery
In Progress
Coming Soon
Model News
Order Form
Contact Us
Want's
Links
 

"FORD MODELS"
Ford - Lincoln - Mercury

Solution Graphics

 

Doug Nash's
BRONCO BUSTER
Ford Bronco Half Cab Long Nose Funny Car


#SC-104 ........ $42.00

I personally guarantee this to be the only correct Bronco Buster ever made !
Visit the "IN PROGRESS" page to see the extensive work that was done to this new model *

NOW AVAILABLE !

 

Resin model includes:Correct Body, Chassis, Straight Tube Front Axle (with coil over shocks),
Ladder Bars, Rear Shocks, Firewall, Cowl, Grill & 2- Front Bumper options.

Recommended donor parts:
#SC-38 Halibrand 15" Front Mag Wheels (use for rear mags on early version)..... Inner Rims are included.
The center cap needs to be drilled out if using these Halibrands.
#SC-57 S/S Cragar Rear Mag Wheels (for later version)
#SC-87  Inner Rims (deep dish)
#SC- 106 American 18" 12 Spoke Mag Wheels
#SC- 105 Ford (small block) Injection "Parts Pack"
#SC-93
Ford 9 Inch Rear End
#SC-7
AFX Parts Pack - Tachometer, Gas Cap, Fuel Pump, Master Cylinder, Timing Balancer Pulley & Steering Box.
#SC-64 Funny Car Parts Pack - Mallory Super Coil, Airheart Disk Brakes & Oil Filter.
#SC-103 Drag Racing Driver Figure

> Use AMT/ERTL 1967 Mustang GT for: 289 Ford small block engine.

> Standard 18" Goodyear or Pirelli Dragster Tires will be needed (found in most dragster kits).

> Use Revell Ford T Roadster for: Headers, Radius Rods & Spindles- (if poseable wheels are desired).

> Use AMT Goodyear Blue Streak 9:00 x 15" Slicks (found in older AMT kits).

> Visit the MODEL NEWS page for tips on making a "Flip Front-End".

> To make the interior tin..... Fit a piece of .020" sheet inside the body,
glue the cowl to the sheet and remove the center section.

> To set the front axle..... Springs should face the rear of the axle. > Use Revell Ford Thunderbolt kit to replace all 4 shocks if desired.

Has new decals specifically fitted to this Speed City Resin body.

> If your familiar with the old Bronco Buster decals, than you know how wrong they are,
from- missing sponsors- inaccurate fonts- incorrect cowboy- rope- etc.
New decals have been completely redesigned to be as accurate as possible.
Decals have the all the markings for the 1966 and '67 version.

The "Bob's Drag Chute" and "Moon Gas Tank tag" are also included on the decal sheet .

Jim Polli built this from a resin model.


 

STONE, WOODS & COOK
DARK HORSE 2
'66 Long Nose AWB Mustang Funny Car



Approved and Authorized by Mike Cook


Mock up using a Polar Lights Charger or Barracuda Funny Car Chassis


#SC-17 ......... $38.00

THIS ITEM IS UNAVAILABLE AT THIS TIME, PLEASE DO NOT ORDER !

 Resin kit includes: Correct Body (with semi-hollow door handles), Interior Tub (with custom seat), 2- Inner Body Bracing's,
Honeycomb Grill, Front Bumper, Thunderbird Tail Lights and Porsche style Trunk Vent.

Recommended donor parts:
#SC-103 Drag Racing Driver Figure
#SC-91 Buick / Olds/ Pontiac Rear End
#SC-66 392 Hemi Engine
#SC-64
Funny Car Parts Pack (for Airheart Disk Brakes, Blower Pulleys, Ideler Arm, 392 Timing Cover,
4-Port Injectors, Tranny Linkage, Oil Filter & MallorySuper Coil.
#SC-83 Ribbed Blower Belt
#SC-57 S/S Cragar Rear Mag Wheels
#SC-87  Inner Rims (deep dish)
#SC-80 Halibrand 16"(deep dish) Rear Mags (for later version)
#SC-75
Goodyear Blue Streak Skinny Front Tires...... (as you can see, the Polar Lights Front Tires are too small)
#SC-34 S/S Cragar (zero offset) Front Mag Wheels

*An amt/ertl '67 Mustang is needed for the Grill Insert and Rear Bumper.

*A Polar Lights Charger or Barracuda Funny Car is need for a donor chassis

*A Monogram/Revell '66 Shelby Mustang GT 350H (for side windows).

*Model King "Hemi Under Glass" for headers..... or make them from solder?

*392 Hemi and Scoop can be found in the Revell Miss Deal.
or use our #SC-66 (1-piece) 392 HEMI ENGINE, found on the "Parts Page".

*The Revell S.W.C Willys (Black) Gasser also has a 392 Hemi Engine and a one-piece Scoop.

*If doing a flip front end, you will need to scribe out the "pre-scribed front clip"
and use the hinge directions on the "MODEL NEWS" page.

Stone, Woods & Cook decals.
(you'll need to reverse the ribbons on the front fenders)

Jim Polli built this from a resin model.

Ran Ramsay built this from a resin model.
Winning 3 category's..... BEST DETAIL, FAST ON THE QUARTER MILE & BEST IN SHOW,
at the Wally Parks N.H.R.A. Motor sports Museum "SPIRT OF SPEED" Model Contest on Nov 8 2015


 

Jack Ditmars'
Lil' SCREAMER
'34/'37 FORD ALTERED COUPE
1/25 scale



#SC-22 ......... $44.00

THIS ITEM IS UNAVAILABLE AT THIS TIME, PLEASE DO NOT ORDER !

Resin model includes: Correct Body, Hood, Frame (with Shackle, roll bar & motor mount locator pins),
Seat, Drive Shaft Tunnel, Firewall/Doghouse, Hilborn Small Block Chevy Injection Manifold and 2-piece Hood Sc
oop.

Recommended donor parts:
#SC-001 Lil Screamer decals
#SC-103 Drag Racing Driver Figure
#SC-93
Ford 9 Inch Rear End
#SC-100 Wheelie Bars
#SC-99
Goodyear Blue Streak 16" Drag Slicks
#SC-85
 American "TORQUE THRUST" 16" Deep Dish Mags (for later version)
#SC-87  Inner Rims (deep dish)
#SC-75
Goodyear Blue Streak Skinny Front Tires
#SC-49 American 12 Spoke Front Mag Wheels
#SC-7 AFX Parts Pack
#SC-25 10" Aluminum Hollow Tube Injector Stacks

*See "MODEL NEWS" page for instructions on how to make a front tube straight axle.

*If building the version with the "Deep Dish Cragar's", those can be found in the MPC "Mummy Machine.

*Originally this car ran a small block 289 Chevrolet Corvette Engine and later to a 350.

Photo's of the roll bar dimensions ........ ......... ......... There are roll bar locator pins on the models chassis.

Scott Kapellusch built this from a resin model.
UPDATE: This model took BEST IN SHOW at the Wally Parks N.H.R.A. Motorsports Museum
"SPIRIT OF SPEED" Model Contest on Nov 5 2017


 

1966 LONG NOSE MUSTANG FUNNY CAR





#SC-19 ......... $42.00

THIS ITEM IS UNAVAILABLE AT THIS TIME, PLEASE DO NOT ORDER !

This is the only accurate '66 Mustang Funny Car on the market
and has the only Correct Altered Front Wheel Base !

Resin model includes: Correct Body (with semi-hollow door handles), Hood, 2- piece Chassis & Interior Tub,
Dash & Custom rear spoiler.

Recommended donor parts:
#SC-103 Drag Racing Driver Figure
#SC-100 Wheelie Bars
#SC-93 Ford 9 Inch Rear End
Check out our "PARTS PAGE" for any Tires, Slicks, Mag Wheels, Rear End or other parts you may need.

*A Model King Mustang Funny Car Kit will be needed for the engine, glass and interior parts.

*Use amt/ertl's '67 Mustang G/T for "alternate" poseable front suspension, rear axle, shocks & leaf springs.

Contact Nikki at: poppawheelie65@yahoo.com for the "Tommy Grove" Mustang decals.

Has the Batcar, Bardahl Ford, Daddy Warbucks & Tasca Ford decals to specifically fit our body !

Jim Polli built this from a resin model.

Doug Schultz built this from a resin model.

Scott Kapellusch built this from a resin model.

Chris Cantler built this from a resin model.


All rights reserved. Do not copy any Speed City Resin bodies or parts without permission and consent.